Chimney cap installation in Freehold, New Jersey that keeps water and wildlife out
Custom stainless and copper caps built for Freehold's freeze-thaw cycles
Chimney cap installation in Freehold, New Jersey protects your flue from rain, snow, squirrels, and sparks. We measure your clay flue tile or stainless steel liner, fabricate a custom chimney cap, and bolt it down with stainless hardware. If your old cap is rusted or missing, chimney cap replacement Freehold New Jersey restores that first line of defense in a single visit. Call (844) 803-5147 for a same-week appointment.
Chimney cap installation in Freehold, New Jersey: what it actually involves
Chimney cap installation in Freehold, New Jersey is the fabrication and mounting of a screened metal cover over your flue. A proper cap has four parts: a spark screen that blocks embers and nesting animals, a solid lid that sheds rain and snow, a mounting frame that fits your exact flue dimensions, and stainless or copper fasteners that won't rust. We measure the flue opening with a video inspection camera, check the crown for cracks, and build the cap to overlap the crown by at least 2 inches on every side.
Freehold's climate is hard on chimneys. Between the freeze-thaw swings from November through March and the summer downpours that dump 2 inches in an hour, an uncapped flue takes on water every season. That water mixes with creosote, weakens refractory mortar, and rusts the damper. Homeowners in Freehold Borough and Freehold Township call us most often after they hear scratching in the flue or spot a water stain on the firebox floor. Affordable Chimney cap installation in Freehold New Jersey is far cheaper than rebuilding a crown or relining a flue.
Why Freehold homeowners cap their chimneys
A chimney cap is the cheapest insurance policy on your roof. Here is what a properly installed cap does for a Freehold home, from stopping leaks to keeping raccoons out of the flue.
Stops water damage
Rain and snowmelt pour straight down an open flue. A cap with a 2-inch crown overhang sheds that water onto the roof, not into your firebox. We have pulled soaked insulation and rotted damper frames out of Freehold chimneys that ran uncapped for years. One $300 cap prevents a $3,000 crown rebuild.
Blocks nesting animals
Squirrels, raccoons, and chimney swifts treat an open flue as a free apartment. Our stainless mesh screens are welded, not stapled, so they hold up against claws and ice. Freehold sits near wooded lots in Adelphia and Colts Neck Crossing, and animal calls spike every spring. A screened cap ends that cycle.
Keeps sparks off the roof
Burning wood throws embers. Without a spark screen, those embers land on asphalt shingles or dry leaves in your gutter. Our caps meet NFPA 211 spark-arrestor requirements, which matters if your home sits near the tree canopy common in West Freehold and East Freehold. It is a small detail that prevents a very large fire.
Cuts downdrafts and odors
A cap with the right clearance reduces wind-driven downdrafts that push smoke back into the room. It also keeps rain from mixing with creosote, which is what causes that sour smoke odor on humid days. Customers in Freehold Center tell us the smell disappears the same week we install the cap.
Our chimney cap installation process
We handle the whole job from measurement to final seal. Most caps are fabricated and installed in one visit, and you get a written price before we start. Here is exactly what happens when you book with us.
Inspection
We start with a video inspection camera run down the flue to check the liner, damper, and creosote level. On the roof, we measure the flue opening, inspect the crown for cracked crown mix, and check the flashing. This takes about 30 minutes and tells us whether a standard cap fits or you need a custom chimney cap Freehold New Jersey fabrication.
Measurement and fabrication
We record the exact outside dimensions of your clay flue tile or stainless steel liner. Most caps are built from 24-gauge stainless steel or 16-ounce copper, with a welded mesh screen sized to your flue. Custom fabrication takes 2 to 5 business days depending on the metal. We confirm the material and finish with you before ordering.
Roof protection setup
On install day we lay drop cloths over the roof and set up ladder stabilizers. We never walk a bare shingle. If your roof pitch is steep, we use roof anchors and OSHA-compliant fall protection. Your gutters and landscaping stay clean, and we haul away the old cap and any debris.
Mounting and sealing
We set the cap over the flue, center it, and fasten it with stainless lag bolts into the flue tile or a masonry anchor. We apply a bead of high-temp silicone where the frame meets the crown. The whole mount takes 45 to 90 minutes. We check level, screen tension, and clearance from the roof surface before we pack up.
Final test and walkthrough
We run a smoke test or a flashlight check from the firebox to confirm the flue is clear and the cap sits square. You get photos of the finished cap from the roof, plus a note on the cap material and warranty. If we found a cracked crown or damaged flashing during inspection, we tell you what it needs and what it costs.
Chimney cap expertise you can verify
Voltira Labs has been installing chimney caps in Freehold since 2021. Our technicians hold CSIA Certified Chimney Sweep credentials and follow NFPA 211 and IRC chimney code on every job. We carry a New Jersey HIC license and full liability coverage. Over 5 years we have fabricated caps for clay flue tile, stainless steel liner, and metal chimney systems across Monmouth County. We stock HomeSaver, Copperfield, and Olympia Chimney Supply components, and we weld our own screens in-house so the mesh gauge matches your flue size.
- CSIA Certified Chimney Sweep on staff for every inspection and cap measurement
- 5 years serving Freehold and Monmouth County since 2021
- Custom fabrication in stainless steel, copper, and powder-coated aluminum
- NFPA 211 and IRC chimney code compliance on every installation
- New Jersey HIC licensed and fully insured for residential roof work
Why Freehold homeowners choose our chimney cap installation
We are a local crew, not a franchise call center. When you book chimney cap installation in Freehold, New Jersey with us, you get a written price, a scheduled window, and a technician who has capped hundreds of Freehold flues.
Same-week scheduling
Most cap installations are booked within 3 to 5 business days. If your cap is missing and rain is coming, we prioritize the job. We also offer 24/7 Chimney cap installation Freehold New Jersey for emergency calls when a storm has torn a cap loose or dropped a tree limb on the flue.
Custom fit, not universal
Big-box caps come in three sizes and fit almost nothing correctly. We measure your flue and build to a quarter-inch tolerance. That means no gaps for squirrels, no rattling in high wind, and a cap that overlaps the crown instead of sitting inside it. It is the difference between a 3-year cap and a 20-year cap.
Upfront pricing, no surprises
You get a written price before we order materials. Standard stainless caps run $275 to $550 installed. Custom copper caps run $450 to $900 depending on size and gauge. If we find a cracked crown or damaged flashing during the inspection, we quote that separately so you can decide.
We fix the cause, not just the cap
A cap on a cracked crown still leaks. During every chimney cap replacement near me Freehold visit, we inspect the crown, flashing, and top course of brick. If we see spalling brick or a failing crown, we tell you and quote the repair. Capping a sound chimney is the goal, and we will not sell you a cap that hides a bigger problem.
What our chimney cap installation includes
Every cap installation starts with a top-to-bottom look at your flue and ends with a mounted, sealed cap. Here is what is covered in the standard price, and what we quote separately if we find it during inspection.
What's Included
Flue measurement and inspection
We run a video inspection camera down the flue and measure the outside dimensions of your clay flue tile or stainless steel liner. We also check the crown, flashing, and top course of brick. This tells us the exact cap size and whether any repair is needed first.
Custom cap fabrication
We build your cap from 24-gauge stainless steel, 16-ounce copper, or powder-coated aluminum, with a welded mesh screen sized to your flue. Standard sizes ship in 2 to 3 days; custom sizes take 5 business days. You approve the material and finish before we order.
Stainless mounting hardware
We fasten the cap with stainless lag bolts into the flue tile or masonry anchors into the crown. No zinc-plated hardware that rusts in two winters. We seal the frame to the crown with high-temp silicone so water cannot wick under the edge.
Crown and flashing check
While we are on the roof, we inspect the crown for cracks and the flashing for lifted edges. If we find a problem, we photograph it and quote the repair. We do not hide a failing crown under a new cap.
Cleanup and photo report
We lay drop cloths, haul away the old cap and debris, and leave your roof and gutters clean. You get photos of the finished cap and a note on the material, gauge, and warranty. The whole visit usually takes 1 to 2 hours.
Chimney cap installation near me in Freehold: problems we solve
Most chimney problems in Freehold start at the top. A missing or failed cap lets water, animals, and sparks into places they should never reach. Here are the four calls we get most often.
Water stains on the firebox floor
Water mixes with creosote, rusts the damper, and weakens refractory mortar. Left alone, it rots the firebox and can cost $2,000 or more to rebuild.
We install a cap with a 2-inch crown overhang that sheds rain and snowmelt onto the roof. We also check the crown and flashing, because a cap alone will not stop a leak that starts at a cracked crown.
Scratching and chirping in the flue
Squirrels, raccoons, and chimney swifts nest in open flues. They block the flue, leave droppings, and can carry parasites into your home. A blocked flue also pushes carbon monoxide back into the room.
We sweep out the nesting debris with chimney brushes and a HEPA vacuum, then install a welded stainless mesh screen. The mesh gauge is sized to your flue so animals cannot pry it open.
Rusty damper and smoke odor
An uncapped flue lets rain hit the damper every storm. The damper seizes open or shut, and wet creosote gives off a sour smell on humid days. A seized-open damper wastes heat all winter.
We repair or replace the damper, then cap the flue so water stops reaching it. Customers in Freehold Center tell us the smoke odor disappears within a week of installation.
Sparks landing on the roof
Burning wood throws embers that can land on shingles or dry gutter debris. In Freehold's wooded neighborhoods, that is a real fire risk. Many insurance carriers ask about spark arrestors.
Our caps meet NFPA 211 spark-arrestor requirements with a welded mesh screen. We size the screen openings to block embers while keeping draft strong. It is a code detail that also protects your roof.
When Freehold homeowners call us for a cap
You bought a Freehold home and the inspection report says the chimney has no cap.
We measure the flue, fabricate a stainless cap, and install it, usually within a week of your call. We also inspect the crown and flashing while we are on the roof and give you a written report.
Your flue is sealed before the first fall rain. You get a documented cap installation for your records and no surprises at the next home inspection.
A nor'easter tore the old cap loose and it is hanging by one bolt.
We tarp the flue if rain is coming, then schedule a same-week replacement. If the frame is sound, we repair it with new stainless bolts and screen. If the metal has failed, we fabricate a new cap.
Water stops entering the flue, and the cap is bolted down with stainless hardware that will not pull loose in the next storm.
You hear animals in the flue in early spring.
We sweep out the nesting material with chimney brushes and a HEPA vacuum, check for blocked flue or damaged liner, then install a welded mesh cap sized to your flue. The whole job is done in one visit.
The flue is clear and screened. Animals cannot get back in, and your draft returns to normal for the next burn season.
Your damper is rusted and there is a water stain on the firebox floor.
We repair or replace the damper, then cap the flue with a 2-inch crown overhang. We also check the crown for cracks, since that is the other common leak path in Freehold's freeze-thaw climate.
The firebox stays dry, the damper works again, and the smoke odor fades. You avoid a firebox rebuild that would have cost thousands.
Tools and methods we use on every cap
Tools & Equipment
Video inspection camera
We run it down the flue to check the liner, damper, and creosote level before we measure for a cap. It shows us blockages and cracks we cannot see from the roof.
Chimney brush and rods
Used to sweep creosote and nesting debris out of the flue before capping. A clean flue lets us confirm the cap size and gives you a safer chimney.
Masonry trowel and jointing tool
For repairing cracked mortar around the crown and top course before the cap goes on. A cap over failing mortar will not seal, so we fix the substrate first.
HEPA vacuum
We vacuum the firebox and surrounding area after sweeping so no creosote dust ends up in your living room. It is a small step that customers notice.
Angle grinder and hammer and chisel
Used to cut out spalling brick and failing mortar joints on Freehold's older chimneys. We repair the masonry, then install the cap on a solid surface.
Drop cloth and roof anchors
We protect your roof and gutters with drop cloths and use OSHA-compliant roof anchors on steep pitches. No bare-shingle walking, no debris in your landscaping.
HomeSaver and Copperfield components
We stock stainless and copper cap components from HomeSaver and Copperfield, and we weld our own screens in-house. That lets us match your flue exactly instead of forcing a universal fit.
Methods
NFPA 211 spark-arrestor standard
Every cap we build meets NFPA 211 for spark arrestors, with welded mesh sized to block embers without choking draft. It is the code reference we use when sizing screens for wood-burning flues in Freehold.
IRC chimney code compliance
We follow IRC chimney code for cap height, clearance, and attachment. That means the cap sits at the right height above the flue and is fastened so wind and ice cannot lift it.
Custom fabrication to quarter-inch tolerance
We measure the flue opening and build the cap frame to a quarter-inch tolerance. That eliminates the gaps that let squirrels in and the rattling that universal caps develop in high wind.
Crown overhang sealing
We size every cap to overhang the crown by at least 2 inches on all sides, then seal the frame to the crown with high-temp silicone. This is the detail that keeps water off the masonry.
CSIA Certified Chimney Sweep inspection protocol
Our inspections follow the CSIA Certified Chimney Sweep checklist: flue, liner, damper, crown, flashing, and cap. You get photos and a written summary so you know exactly what we found.
How chimney cap installation runs in Freehold
Freehold sits in a freeze-thaw belt that swings above and below 32 degrees 30 to 40 times each winter. That cycle opens mortar joints and cracks crowns, which is why so many Freehold chimneys leak even when they have a cap. We start every job by checking the crown and top course before we mount anything. If the crown is cracked, we repair it with chimney crown mix first, then install a cap that overhangs the new crown by 2 inches. Freehold's housing stock runs from 1890s brick chimneys in Freehold Borough to 1990s metal systems in Raintree, so we carry caps for clay flue tile, stainless steel liner, and Selkirk or DuraVent pipe. If you need same day chimney cap replacement Freehold, call before noon and we will do our best to get a technician out the same day. Most standard caps are installed in 1 to 2 hours, and we leave the roof cleaner than we found it.
Service Areas
Older brick chimneys with clay flue tile and original mortar. Many have never been capped, so we see water damage and spalling brick on the top course.
Metal chimney systems and prefab fireplaces are common here. Caps must be sized to the pipe, not the masonry, so we stock Selkirk and DuraVent fittings.
Tree canopy and wooded lots mean animal calls every spring. Welded mesh screens are the fix, and we size them to the flue so squirrels cannot pry them open.
Larger lots with tall chimneys and steep roof pitches. We bring roof anchors and OSHA-compliant fall protection for safe access.
Newer construction with stainless steel liners and multi-flue caps. We fabricate caps that cover two or three flues in a single frame.
Local Considerations
Freeze-thaw cycles from November through March
Water enters cracks, freezes, and expands, which spalls brick and opens mortar joints. A cap that overhangs the crown by 2 inches keeps that water off the masonry.
Summer downpours of 2 inches per hour
An open flue takes on water fast during a storm. A solid lid with proper overhang sheds that volume onto the roof instead of into your firebox.
Wooded lots and nearby tree canopy
Squirrels, raccoons, and chimney swifts look for open flues in spring. A welded stainless mesh screen sized to your flue blocks them without choking draft.
Older brick chimneys with clay flue tile
Clay tile cracks over decades, and an uncapped flue speeds that up. We inspect the liner with a video camera and recommend relining before capping if the tile has failed.
Uncapped 1920s brick flue in Freehold Borough
A 1920s brick chimney with no cap, a rusted damper, and water stains on the firebox floor. The crown had two hairline cracks, and the top course of brick showed spalling from years of freeze-thaw water intrusion.
We repaired the crown with chimney crown mix, replaced the damper, and installed a custom stainless cap with a 2-inch overhang. The firebox stayed dry through the next winter, and the smoke odor cleared within a week.
Maintenance & Follow-up
Inspect the cap and screen each fall, re-torque the stainless bolts, and sweep the flue annually. The crown should be rechecked every 3 years for new hairline cracks.
A West Freehold homeowner heard scratching in the flue in April. The open flue had a nest of leaves and insulation about 3 feet down, blocking draft and pushing smoke back into the living room on the first test burn.
We swept the flue with chimney brushes and a HEPA vacuum, checked the liner with a video camera, and installed a welded stainless mesh cap sized to the flue. Draft returned to normal, and no animals have entered in two seasons.
Maintenance & Follow-up
Check the screen each spring for bent mesh or loose bolts. If you burn often, sweep the flue once a year and confirm the cap is still centered over the flue.
A nor'easter pulled a 12-year-old cap loose on a Raintree metal chimney. It hung by one bolt, and rain was running down the outside of the pipe into the ceiling framing. The homeowner called us on a Friday afternoon.
We tarped the flue the same day, then fabricated a new cap sized to the Selkirk pipe and installed it with stainless hardware on Monday. The ceiling stain stopped spreading, and the new cap has held through two subsequent storms.
Maintenance & Follow-up
After any storm with 50 mph gusts, check the cap bolts from the ground with binoculars. Have the fasteners re-torqued every 2 years and replace the screen if it bends.
How much does Chimney cap installation cost in Freehold New Jersey?
Most chimney cap installations in Freehold run $275 to $550 for a standard stainless steel cap, and $450 to $900 for custom copper. The price depends on flue size, metal gauge, and whether the cap is stock or fabricated. Multi-flue caps cost more because they cover two or three openings. We give you a written price before ordering materials, and installation is included.
What size chimney cap do I need in Freehold?
You need a cap that overlaps your flue by at least 2 inches on every side. A standard 8x8 clay flue tile takes a 13x13 cap; a 13x13 flue takes an 18x18. We measure the outside dimensions of your flue tile or stainless steel liner with a video inspection camera and build to a quarter-inch tolerance. Universal caps rarely fit correctly.
Who does chimney cap replacement near me in Freehold New Jersey?
Voltira Labs handles chimney cap replacement across Freehold Borough, Freehold Township, and the surrounding Monmouth County neighborhoods. We have been in business since 2021 and hold CSIA Certified Chimney Sweep credentials. Call (844) 803-5147 and we will schedule a measurement, usually within 3 to 5 business days, or sooner for storm damage.
Do chimney caps prevent water damage in Freehold?
Yes. A cap with a solid lid and a 2-inch crown overhang sheds rain and snowmelt onto the roof instead of down the flue. That stops the water that rusts dampers, weakens refractory mortar, and causes smoke odor. In Freehold's freeze-thaw climate, an uncapped flue can take on water 30 to 40 times a winter. A cap is the cheapest way to stop it.
Credentials and reviews
Certifications
Reviews
Voltira Labs installed a custom stainless cap on our Freehold Borough chimney. They measured the flue, showed us photos of the cracked crown, and repaired it before capping. The price matched the quote, and the crew cleaned up the roof. No more water in the firebox.
We had squirrels in the flue and called three companies. Voltira Labs was the only one that measured the flue and built a welded screen cap to fit. They swept out the nest and HEPA vacuumed the firebox. Fair price and they showed up when they said they would.
Storm tore our cap off in Raintree and rain was coming in. They tarped the flue the same day and installed a new cap sized to our metal chimney on Monday. Clear communication, licensed crew, and the new cap has held through two more storms.
Had a copper cap fabricated for an odd-sized flue. Two other companies tried to sell a universal cap that did not fit. Voltira Labs built one to the exact dimensions and replaced the flashing while they were up there. It looks great and the draft is better than ever.
Related Services
Chimney Repair Near Me
If your flue has cracked tiles or a failing damper, a cap alone will not fix it. We diagnose the whole chimney and repair the liner, crown, or flashing before capping. Freehold homeowners get one crew for the full repair.
Chimney Repair Near MeChimney Masonry Repair
Freehold's freeze-thaw cycles spall brick and open mortar joints. We repoint with tuckpointing mortar and replace damaged brick before installing a cap, so the cap sits on a solid crown and top course.
Chimney Masonry RepairChimney Crown Repair
A cracked crown lets water pool around the flue. We rebuild crowns with chimney crown mix and then install a cap that overhangs the new crown by 2 inches, which is the detail that keeps water off the masonry.
Chimney Crown RepairChimney Relining
If your clay flue tile is cracked or your liner is damaged, we install a stainless steel liner sized to the appliance. We then fabricate a cap to fit the new liner's outside dimensions so the top seal is correct.
Chimney ReliningChimney Cap Repair
Sometimes the cap just needs new bolts, a new screen, or a straightened lid. We repair rusted and storm-damaged caps when the frame is still sound, and replace them when the metal has failed. Freehold customers get an honest call.
Chimney Cap RepairChimney Maintenance
Annual maintenance keeps the cap tight and the flue clear. We inspect the cap, screen, crown, and flashing each year, sweep creosote, and re-torque fasteners. It is the cheapest way to avoid a mid-winter repair in Freehold.
Chimney MaintenanceFireplace Repair
A cap that stops water protects your firebox and damper. If you already have a rusty damper or smoke odor, we repair the fireplace and install the cap in the same visit so the problem does not return.
Fireplace RepairEmergency Chimney Repair
Storm tore your cap off or dropped a limb on the flue? We tarp the opening and schedule emergency repair. Freehold customers can reach us at (844) 803-5147 for same-day response when water is entering the chimney.
Emergency Chimney Repair24/7 Chimney Repair
Chimney problems do not wait for business hours. Our 24/7 line handles Freehold calls for missing caps, active leaks, and blocked flues. We triage the call and get a technician out as fast as the schedule allows.
24/7 Chimney RepairChimney Leak Repair
Most chimney leaks start at the top: a missing cap, a cracked crown, or failed flashing. We trace the leak with a video inspection camera and water test, then fix the source and install a cap that keeps it dry.
Chimney Leak RepairProfessional Chimney Repair
From crown to damper, we handle the full chimney system. Our CSIA Certified Chimney Sweep technicians diagnose the problem, quote the repair, and complete the work. Freehold homeowners get one licensed crew for everything.
Professional Chimney RepairChimney Inspection Service
Every cap installation starts with an inspection. We run a video camera down the flue, check the crown and flashing, and measure the flue opening. You get photos and a written summary of what we find.
Chimney Inspection ServiceChimney Cleaning Service
Creosote buildup is a fire hazard, and a cap does not remove it. We sweep the flue with chimney brushes and rods, then HEPA vacuum the firebox. Freehold customers often pair a sweep with cap installation in one visit.
Chimney Cleaning ServiceChimney Restoration
For badly weathered Freehold chimneys, restoration means rebuilding the crown, repointing brick, and installing a new cap. We bring the whole stack back to code and top it with a cap built to last decades.
Chimney RestorationChimney Liner Repair
A damaged liner lets heat and carbon monoxide into the walls. We repair or replace the liner with a stainless steel liner, then cap the flue to protect the new liner from water and debris.
Chimney Liner RepairFireplace Restoration
Water damage from an uncapped flue ruins fireboxes and hearths. We restore the firebox with firebrick and refractory mortar, then install a cap so the repair stays dry. Freehold fireplaces get a second life.
Fireplace RestorationFireplace Installation
Adding a wood stove or fireplace insert? We install the appliance, line the flue, and cap it with a screened cap sized to the new liner. The cap is the final step that makes the installation weather-tight.
Fireplace InstallationChimney Tuckpointing
Freehold's freeze-thaw cycles open mortar joints. We grind out failing mortar with an angle grinder and repack it with tuckpointing mortar. A cap on top keeps water out of those new joints.
Chimney TuckpointingChimney Waterproofing
We apply a vapor-permeable water repellent to the brick after capping. The cap stops water from above, and the repellent stops it from soaking in sideways. Together they add years to a Freehold chimney.
Chimney WaterproofingChimney Mortar Repair
Cracked mortar around the crown and top course is the first sign of water damage. We repair the mortar with a masonry trowel and jointing tool, then install a cap that overhangs the repair and keeps it dry.
Chimney Mortar RepairChimney Sweep
Our CSIA Certified Chimney Sweep technicians remove creosote with chimney brushes and rods. We HEPA vacuum the firebox and check the cap and screen while we are on the roof. Freehold sweeps include a top-to-bottom look.
Chimney SweepChimney Sweep Near Me
If you are searching for a chimney sweep near me in Freehold, we cover Freehold Borough, Freehold Township, and the surrounding neighborhoods. We sweep, inspect, and can install a cap in the same visit.
Chimney Sweep Near MeChimney Flashing Repair
Damaged flashing is the second most common chimney leak after a missing cap. We replace flashing with new metal and seal it, then cap the flue so water never reaches the flashing from above.
Chimney Flashing RepairResidential Chimney Repair
We work on residential chimneys only, which means our tools and methods are tuned to homes. From brick chimneys in Freehold Borough to metal systems in Raintree, we repair and cap them all.
Residential Chimney RepairBrick Chimney Repair
Spalling brick and cracked mortar are common on Freehold's older brick chimneys. We replace damaged brick, repoint joints, and cap the flue to stop the water that caused the damage in the first place.
Brick Chimney RepairRoof Chimney Repair
Work at the roof line includes flashing, crown, and cap. We repair all three in one visit, using roof anchors and OSHA-compliant fall protection. Freehold roofs stay clean and your chimney gets sealed.
Roof Chimney RepairChimney Damper Repair
A rusty damper is often the first sign of an uncapped flue. We repair or replace the damper, then install a cap so water stops reaching it. Freehold customers get both fixes in one appointment.
Chimney Damper RepairMetal Chimney Repair
Metal chimney systems need a cap sized to the pipe, not the masonry. We fabricate caps for Selkirk and DuraVent systems and seal the joint with high-temp silicone. Freehold metal chimneys get a correct fit.
Metal Chimney RepairSame Day Chimney Repair
When a storm takes your cap off, same day chimney repair matters. We tarp the flue, schedule the fix, and install a new cap as fast as materials allow. Call (844) 803-5147 for Freehold same-day service.
Same Day Chimney RepairBook chimney cap installation in Freehold, New Jersey this week
We are a CSIA Certified Chimney Sweep crew serving Freehold since 2021. Call (844) 803-5147 and we will measure your flue, quote a custom cap, and schedule installation, usually within 3 to 5 business days.